Midea Dehumidifier EH Error Code

                    What EH Error Means: The EH error code on Midea dehumidifiers indicates a humidity sensor malfunction or communication failure [[6]]. This can also appear as EH60 on Cube models, pointing to sensor or water tank issues [[1]]. The unit cannot properly detect moisture levels and requires immediate attention.
                

Quick Fix / Soft Reset

Try these steps first before disassembling the unit:

1 Power off the unit using the control panel button

2 Unplug from the wall outlet completely

3 Check the water tank – ensure it’s properly seated and the float moves freely [[1]]

4 Wait 5-10 minutes for the system to fully reset

5 Plug back in and restart. If EH persists, continue with detailed troubleshooting

🔍 Common Causes of EH Error

🔌

Loose Wiring

Sensor harness disconnected or corroded connections

💧

Faulty Sensor

Humidity sensor/thermistor has failed or is out of range

🧊

Tank Issue

Water tank not properly positioned or float stuck [[1]]

️

Board Failure

Control board cannot read sensor data properly

🔧 Step-by-Step Troubleshooting

🔧 Tools Needed: Phillips screwdriver, flathead screwdriver, digital multimeter, soft cloth, compressed air

1

Verify Water Tank Position

EH60 specifically can indicate the water tank isn’t properly seated [[1]].

Remove the water tank completely

Check that the float mechanism moves freely up and down

Clean any debris from the tank compartment

Reinsert the tank firmly until it clicks into place

Ensure the tank is not overfilled or cracked

2

Inspect Humidity Sensor Connections

How to access: Unplug the dehumidifier. Remove the back panel screws. Use a flathead screwdriver to gently release the top housing clips and lift to expose the control board.

What to check: Locate the humidity sensor wiring harness. Disconnect and reconnect the sensor plug at the control board. Inspect for:

Corroded or bent pins in the connector
Frayed or pinched wires
Loose connections at both ends
Water damage or moisture on the board

3

Test the Humidity Sensor

Testing procedure: Disconnect the sensor from the control board. Set multimeter to Ohms (Ω). Touch probes to the sensor terminals.

                            Expected readings: At room temperature (70°F/21°C), the sensor should read between 10kΩ and 15kΩ. Readings of “OL” (open circuit) or “0” (short circuit) indicate a failed sensor that needs replacement [[6]].
                        

4

Clean the Sensor Probe

Dust and debris can interfere with sensor readings.

Locate the sensor probe (usually near the air intake)

Gently wipe with a soft, dry cloth

Use compressed air to blow away dust

Do NOT use water or cleaning solutions

Ensure the probe is not bent or damaged

5

Examine the Control Board

If the sensor tests correctly, the problem may be on the board.

Visual inspection: Look for:

Burnt or discolored components
Bulging or leaking capacitors
Corroded solder joints around sensor pins
Cracked traces or physical damage

                            Warning: If you find board damage, professional repair or replacement is recommended.
                        

🛒 Parts Replacement Guide

If testing confirms the humidity sensor has failed, you’ll need to order a replacement part.

OEM Replacement Part

Order the Humidity Sensor Assembly or Humidity Sensor Harness specific to your Midea model number (check the label on your unit, e.g., MAD50PS1WWT, MAD35S1QWT). Search using your exact model number on:

Midea official parts website
Authorized service centers
Appliance parts retailers (Repair Clinic, PartSelect)

💡 Budget Alternative

If OEM parts are unavailable or expensive, you can use a generic 10kΩ or 15kΩ NTC thermistor with a compatible 2-pin connector. Available on Amazon, eBay, or AliExpress for $10-20. Verify:

Resistance value matches original (10kΩ or 15kΩ)
Connector type matches (usually JST connector)
Probe length is similar to original

                        Pro Tip: When installing the new sensor, apply a small amount of dielectric grease to the connector pins to prevent future corrosion.
                    

🛡️ Prevention Tips

                    To prevent EH errors in the future:
                    Clean the air filter monthly to ensure proper airflow
Empty the water tank before it reaches maximum level
Keep the unit in a location with stable temperature (avoid garages or unheated spaces)
Vacuum around the air intake regularly to prevent dust buildup on the sensor
Run the dehumidifier at least once a month during off-season to keep components active

                

⚠️

Repair vs Replace Decision

Consider the cost-effectiveness before proceeding with repairs.

✅ WORTH REPAIRING:

Simple sensor replacement ($15-40 part cost)
Loose wiring connection (free fix)
Unit is under warranty (contact Midea support)
Dehumidifier is less than 3 years old

❌ BUY NEW INSTEAD:

Control board replacement needed ($80-150)
Unit is over 5 years old
You notice refrigerant leaks (oily residue on coils)
Compressor makes loud grinding noises
Multiple error codes appear simultaneously

Make an Informed Decision

🚨 When to Call Professional Help

Contact Midea Customer Service or a certified HVAC technician if:

The EH error persists after sensor replacement
You see visible damage to the control board
The unit is still under warranty (DIY repairs may void warranty)
You’re uncomfortable working with electrical components
The dehumidifier shows other symptoms like not cooling or unusual noises

Midea Support: Check your user manual or visit the Midea website for authorized service centers [[2]][[5]].